AN INNOVATION IN AUTOMOTIVE INDUSTRY Seminar
ABSTRACT
-The increasing demands for low emissions and low fuel consumption in modern combustion engines require improved methods for combustion process.
The Beare Head is a new type of six-stroke engine head design known as the “Beare Head” after its designer, Malcolm Beare. The Beare Head uses a piston and ports very much like a two stroke engine to replace the overhead valve system that is found in four stroke engines today. The four-stroke block, piston and crankshaft remain unaltered. This combination of two stroke and four-stroke technology has given the technology its name the “six stroke engine”.
I.INTRODUCTION
Malcolm Beare, an Australian wheat farmer began working 17 years ago on a stratified charge opposed-piston two-stroke design, but after building a couple of prototypes. The flow control was a problem, with too many ports going everywhere. So he simplified it into a six-stroke with the objective of improving efficiency and increasing performance compared to a conventional engine by overcoming the drawbacks of poppet valves, by means of a rotary valve application to four-stroke engine technology. Rotary valve designs aimed at overcoming the problems of poppet valves - inertia, inhibiting flow and especially the exhaust valve hot spot in the combustion chamber.
Of course, a two-stroke doesn't suffer such problems because it has no poppet valves – so he tries to resolve these drawbacks. By taking the basic components of a rotary disc induction two-stroke engine, and grafting them on to a four-stroke to produce the best of both worlds.
Fig.1.View of a 6-Stroke Engine Fig.2. Transplantation of Beare Engine
II.CONSTRUCTION USES
Below the cylinder head gasket, everything is conventional; so one advantage is that the Beare concept can be transplanted on to existing engines without any need for redesigning or retooling the bottom end. But the cylinder head and its poppet valves get thrown away. To replace the camshaft and valves, retained the cam drive belt and fit an ultra short-stroke upper crankshaft complete with piston, which the belt drives at half engine speed just as it previously drove the cam. This piston drives up and down in a sleeve, past inlet exhaust ports set into the cylinder wall, very much like on a two-stroke: these are all exposed during both inlet and exhaust strokes.
During the compression and expansion strokes, the upper piston seals off both ports, leaving the pressure contained between the two pistons, with the lower one a conventional flat-top three-ring design, while the conical upper one (so shaped to aid gas flow during both inlet and exhaust cycles by guiding it towards the ports) has two rings - one compression, one oil. In the combustion phase, twin spark plugs provide ignition via the stock Ducati CDI and a pair of Harley coils - one per cylinder - and not only does the engine run on pure petrol (no need to add oil, because all required surfaces are positively lubricated, in spite of the application of two-stroke technology), it's also happy on low octane unleaded fuel. Obviously there are no valve seats to suffer from lack of lead, and it is said that the compression ratio can be increased significantly from the Ducati motor's 10.6:1 quite safely because of the lack of hotspots, without problems with detonation.
So now the claimed advantages of all this start to come to light - allowing a higher compression while still happy with low octane unleaded makes this an efficient and cleaner engine. There are no poppet valves to float or bend. In turn, this implies a far higher safe rev limit for the six-stroke - 28,000rpm in theory, given the half-engine speed operation of the upper crankshaft, and the fact that GP reed-valve two-strokes peak at 14,000rpm. But the rev limit, as on such two-strokes, depends only on what the main (conventional) crankshaft is able to bear, and he's arbitrarily limited the Ducati-based 6S-V2 to 9,000rpm for that reason, at which point he says (according to computer predictions) 86bhp is delivered at the rear wheel.
Comparisons are hard to make, because of the difficulty of determining the exact cubic capacity of the 6S-V2's six-stroke engine: what began as an elderly Pantah V-twin now has a total 744cc's of compression/expansion volume, and 602cc of inlet/exhaust volume, and instead of absorbing about 10% of engine power in driving the camshafts, the cam belts now deliver about 9% net power to the main crankshaft after combustion via the upper, conical porting piston. But if you figure that a '97 model Ducati 900SS delivers 73bhp at the rear wheel in stock form, that's quite an impressive claimed power increase.
III.COMBUSTION PROCESS
1. INTAKE STROKE
The intake stroke begins when the bottom piston is on its downward stroke. And the rotary valve cuts exhaust port and the inlet port is opened by the top piston. Suction of charge is due to the pressure difference.
2. INTAKE CONTINUES
Intake continues till the bottom piston reaches the bottom dead center and the top piston seals the inlet port completely.
3. COMPRESSION STROKE
During the compression stroke the bottom piston moves from bottom dead center to top dead center this reduces the volume inside the cylinder and this increases the temperature and pressure.
4. EXPANSION STROKE
During the expansion stroke, the fuel ignites and the combustion starts at the end of compression stroke when the piston approaches top dead center position. In the combustion process the chemical energy of the fuel is released and there is rise in temperature and pressure. Thus the explosion forces the bottom piston down to turn the engine’s crankshaft, delivering the power via the gearbox and clutch to the driving wheels.
5. EXHAUST STROKE
During the exhaust stroke the rotary valve opens, allowing the exhaust gases to escape and the bottom piston moves from bottom dead center to top dead center
6. EXHAUST STROKE CONTINUES
The piston is in the second upward path. Exhaust stroke continues till all the exhaust gasses escape and the rotary valve cuts the exhaust port. Exhaust stroke ends, intake port opens and the fresh charge is drawn in and the whole process is repeated again
V.THEORY OF SIX STROKE IC ENGINE
VOLUME ANGLE DIAGRAM
PRESSURE VOLUME DIAGRAM
TORQUE ANGLE DIAGRAM
-The increasing demands for low emissions and low fuel consumption in modern combustion engines require improved methods for combustion process.
The Beare Head is a new type of six-stroke engine head design known as the “Beare Head” after its designer, Malcolm Beare. The Beare Head uses a piston and ports very much like a two stroke engine to replace the overhead valve system that is found in four stroke engines today. The four-stroke block, piston and crankshaft remain unaltered. This combination of two stroke and four-stroke technology has given the technology its name the “six stroke engine”.
I.INTRODUCTION
Malcolm Beare, an Australian wheat farmer began working 17 years ago on a stratified charge opposed-piston two-stroke design, but after building a couple of prototypes. The flow control was a problem, with too many ports going everywhere. So he simplified it into a six-stroke with the objective of improving efficiency and increasing performance compared to a conventional engine by overcoming the drawbacks of poppet valves, by means of a rotary valve application to four-stroke engine technology. Rotary valve designs aimed at overcoming the problems of poppet valves - inertia, inhibiting flow and especially the exhaust valve hot spot in the combustion chamber.
Of course, a two-stroke doesn't suffer such problems because it has no poppet valves – so he tries to resolve these drawbacks. By taking the basic components of a rotary disc induction two-stroke engine, and grafting them on to a four-stroke to produce the best of both worlds.
Fig.1.View of a 6-Stroke Engine Fig.2. Transplantation of Beare Engine
II.CONSTRUCTION USES
Below the cylinder head gasket, everything is conventional; so one advantage is that the Beare concept can be transplanted on to existing engines without any need for redesigning or retooling the bottom end. But the cylinder head and its poppet valves get thrown away. To replace the camshaft and valves, retained the cam drive belt and fit an ultra short-stroke upper crankshaft complete with piston, which the belt drives at half engine speed just as it previously drove the cam. This piston drives up and down in a sleeve, past inlet exhaust ports set into the cylinder wall, very much like on a two-stroke: these are all exposed during both inlet and exhaust strokes.
During the compression and expansion strokes, the upper piston seals off both ports, leaving the pressure contained between the two pistons, with the lower one a conventional flat-top three-ring design, while the conical upper one (so shaped to aid gas flow during both inlet and exhaust cycles by guiding it towards the ports) has two rings - one compression, one oil. In the combustion phase, twin spark plugs provide ignition via the stock Ducati CDI and a pair of Harley coils - one per cylinder - and not only does the engine run on pure petrol (no need to add oil, because all required surfaces are positively lubricated, in spite of the application of two-stroke technology), it's also happy on low octane unleaded fuel. Obviously there are no valve seats to suffer from lack of lead, and it is said that the compression ratio can be increased significantly from the Ducati motor's 10.6:1 quite safely because of the lack of hotspots, without problems with detonation.
So now the claimed advantages of all this start to come to light - allowing a higher compression while still happy with low octane unleaded makes this an efficient and cleaner engine. There are no poppet valves to float or bend. In turn, this implies a far higher safe rev limit for the six-stroke - 28,000rpm in theory, given the half-engine speed operation of the upper crankshaft, and the fact that GP reed-valve two-strokes peak at 14,000rpm. But the rev limit, as on such two-strokes, depends only on what the main (conventional) crankshaft is able to bear, and he's arbitrarily limited the Ducati-based 6S-V2 to 9,000rpm for that reason, at which point he says (according to computer predictions) 86bhp is delivered at the rear wheel.
Comparisons are hard to make, because of the difficulty of determining the exact cubic capacity of the 6S-V2's six-stroke engine: what began as an elderly Pantah V-twin now has a total 744cc's of compression/expansion volume, and 602cc of inlet/exhaust volume, and instead of absorbing about 10% of engine power in driving the camshafts, the cam belts now deliver about 9% net power to the main crankshaft after combustion via the upper, conical porting piston. But if you figure that a '97 model Ducati 900SS delivers 73bhp at the rear wheel in stock form, that's quite an impressive claimed power increase.
III.COMBUSTION PROCESS
1. INTAKE STROKE
The intake stroke begins when the bottom piston is on its downward stroke. And the rotary valve cuts exhaust port and the inlet port is opened by the top piston. Suction of charge is due to the pressure difference.
2. INTAKE CONTINUES
Intake continues till the bottom piston reaches the bottom dead center and the top piston seals the inlet port completely.
3. COMPRESSION STROKE
During the compression stroke the bottom piston moves from bottom dead center to top dead center this reduces the volume inside the cylinder and this increases the temperature and pressure.
4. EXPANSION STROKE
During the expansion stroke, the fuel ignites and the combustion starts at the end of compression stroke when the piston approaches top dead center position. In the combustion process the chemical energy of the fuel is released and there is rise in temperature and pressure. Thus the explosion forces the bottom piston down to turn the engine’s crankshaft, delivering the power via the gearbox and clutch to the driving wheels.
5. EXHAUST STROKE
During the exhaust stroke the rotary valve opens, allowing the exhaust gases to escape and the bottom piston moves from bottom dead center to top dead center
6. EXHAUST STROKE CONTINUES
The piston is in the second upward path. Exhaust stroke continues till all the exhaust gasses escape and the rotary valve cuts the exhaust port. Exhaust stroke ends, intake port opens and the fresh charge is drawn in and the whole process is repeated again
V.THEORY OF SIX STROKE IC ENGINE
VOLUME ANGLE DIAGRAM
PRESSURE VOLUME DIAGRAM
TORQUE ANGLE DIAGRAM
V.DISCUSSION ON THEORY
According to the theory more torque is derived if the upper piston drive is advanced in relation to the main crank. This would be so if all other factors remain constant. Advancing the upper piston drive has detrimental effects on valve timing, combustion chamber volume and rate of change in volume during the combustion period and total engine volume.
(1) Valve Timing. The effect is to open the exhaust port earlier, reduce the amount of valve overlap and close the intake port earlier. Opening the exhaust port earlier means that the expansion stroke is effectively shortened and less energy is extracted. Reducing the amount of overlap does not allow enough time for intake to clear the combustion chamber and the exhaust extraction effect is reduced. The earlier intake port closing reduces charge filling and volumetric efficiency.
(2) Combustion chamber volume is effectively increased thus lowering compression ratio. The rate of acceleration of expansion is faster in the earlier periods, contrary to the ideal of a constant volume during combustion.
(3) Total Engine Volume. The effect is to reduce change in volume during intake and compression and increase expansion and exhaust, thus reducing volumetric efficiency of intake.
If we do advance the timing we would have to compensate in the design of the engine by
• Reducing combustion chamber volume
• Raising exhaust port lower lip to provide later exhaust opening
• Lowering intake port lower lip to provide later intake closing.
• Altering disc timing to allow later exhaust port closing
NON-PARASITIC DRAG
In practical tests, actually retarding the upper piston drive has a positive outcome on power output and efficiency largely because it effectively increases compression ratio, reduces the rate of change in volume during the combustion period, opens the exhaust port later, increases the period of valve overlap thus utilizing the exhaust extraction effect and closes the intake port later. The negative effect of this is to increase the amount of energy input to the head, but this is more than compensated by the positive outcomes.
The Six-stroke engine is fundamentally superior to the four stroke because the head is no longer parasitic but is a net contributor to - and an integral part of - the power generation within the engine. The Six stroke is thermodynamically more efficient because the change in volume of the power stroke is greater than the intake stroke, the compression stroke, and the exhaust stroke. The compression ratio can be increased because of the absence of hot spots and the rate of change in volume during the critical combustion period is less than in a Fourstroke.The absence of valves within the combustion chamber allows considerable design freedom.
According to the theory more torque is derived if the upper piston drive is advanced in relation to the main crank. This would be so if all other factors remain constant. Advancing the upper piston drive has detrimental effects on valve timing, combustion chamber volume and rate of change in volume during the combustion period and total engine volume.
(1) Valve Timing. The effect is to open the exhaust port earlier, reduce the amount of valve overlap and close the intake port earlier. Opening the exhaust port earlier means that the expansion stroke is effectively shortened and less energy is extracted. Reducing the amount of overlap does not allow enough time for intake to clear the combustion chamber and the exhaust extraction effect is reduced. The earlier intake port closing reduces charge filling and volumetric efficiency.
(2) Combustion chamber volume is effectively increased thus lowering compression ratio. The rate of acceleration of expansion is faster in the earlier periods, contrary to the ideal of a constant volume during combustion.
(3) Total Engine Volume. The effect is to reduce change in volume during intake and compression and increase expansion and exhaust, thus reducing volumetric efficiency of intake.
If we do advance the timing we would have to compensate in the design of the engine by
• Reducing combustion chamber volume
• Raising exhaust port lower lip to provide later exhaust opening
• Lowering intake port lower lip to provide later intake closing.
• Altering disc timing to allow later exhaust port closing
NON-PARASITIC DRAG
In practical tests, actually retarding the upper piston drive has a positive outcome on power output and efficiency largely because it effectively increases compression ratio, reduces the rate of change in volume during the combustion period, opens the exhaust port later, increases the period of valve overlap thus utilizing the exhaust extraction effect and closes the intake port later. The negative effect of this is to increase the amount of energy input to the head, but this is more than compensated by the positive outcomes.
The Six-stroke engine is fundamentally superior to the four stroke because the head is no longer parasitic but is a net contributor to - and an integral part of - the power generation within the engine. The Six stroke is thermodynamically more efficient because the change in volume of the power stroke is greater than the intake stroke, the compression stroke, and the exhaust stroke. The compression ratio can be increased because of the absence of hot spots and the rate of change in volume during the critical combustion period is less than in a Fourstroke.The absence of valves within the combustion chamber allows considerable design freedom.
0 comments:
Post a Comment